Block landing · plant plan view top cad block
Plant plan view top CAD block in DWG in 2026
By Saumyajit Maity · Published 14 Nov 2025 · Updated 10 Mar 2026
Every floor plan needs plants seen from above, not from the side: the round canopy symbol that marks a pot in a corner, a row of planters along a façade, or greenery on a roof terrace. This free plant plan view (top) CAD block provides that top-down symbol in DWG for AutoCAD 2004 or later. It is free for personal and commercial work, with no signup, no watermark and no attribution.
The distinction matters: an elevation plant block dropped into a plan reads as a flat blob, while a proper plan-view symbol shows the canopy footprint the way a plan is meant to. This block is drawn for plan use — a circular or organic canopy outline that occupies the correct footprint — so it lands cleanly in floor plans, furniture layouts and roof and terrace plans wherever you need to mark planting from above.
What the plan-view plant block shows
The block draws a plant from directly above: a roughly circular or softly irregular canopy outline, sometimes with a smaller pot circle inside it to mark the container, so the symbol reads as planting seen in plan. The canopy edge is kept clean — either a smooth circle or a gently lobed outline — so it represents the footprint the plant occupies on the floor without fussy detail.
This is fundamentally a footprint symbol: what matters in plan is how much floor area the plant takes and where its centre sits. The outline is built so you can hatch it lightly to suggest foliage or leave it as a simple circle, and it sits on linework you can put on a planting layer and screen back like any other plan symbol.
Views and what's included
This is a plan-view (top) block: the plant seen from above for floor plans, furniture layouts, landscape plans and roof and terrace drawings. It is the counterpart to the elevation plant blocks — use this one wherever you are looking down at the space, and the elevation versions wherever you are looking at a wall.
The canopy and any inner pot circle sit on linework you can hatch or screen, and the block inserts as a single reference centred on the plant so you can place it precisely and array it along a façade or planter run. Explode it only if you want to adjust the canopy outline for a particular plant footprint.
Typical sizing to design around
In plan, what you scale is the canopy footprint — the diameter of the circle the plant occupies on the floor. As a planning range, a small pot plant footprint is modest, while a large feature plant or planter spreads to a noticeably bigger circle; the inner pot circle, where shown, is smaller again. Use the floor plan's real dimensions as your guide and size the canopy so the planting reads at the correct footprint against the furniture and walls around it.
These are ranges to design within, not fixed numbers on the block. Because plan symbols are all about footprint, the key check is the diameter against the space — a planter that would block a walkway in reality should read that way in plan. As a single block reference, the symbol scales freely so you can match it to the real canopy or pot size.
How to insert and array it
The DWG is drawn in millimetres. Insert at scale 1 in a millimetre drawing, 0.001 in a metre template, or set INSUNITS to millimetres in an imperial file so AutoCAD rescales the block automatically and the canopy lands at the right footprint.
Use INSERT or drag the file in, pick the centre of the canopy as the insertion point, and place it where the plant centre sits in the plan. Because the symbol is centred, it arrays cleanly: use ARRAY to repeat planters evenly along a façade, a path or a terrace edge, and a path array to follow a curved planting line. Keep the planting on its own layer so you can freeze it for a structural plan and thaw it for the furnished or landscaped layout.
Where plan-view plant symbols are used
Plan-view plant blocks are everywhere a drawing looks down: interior furniture layouts and FF&E plans, landscape and site plans, roof terrace and balcony plans, public-realm and courtyard layouts, and reception and lobby plans. They mark where planting sits and how much floor it claims, which is exactly the information a plan must carry.
They pair naturally with the elevation plant blocks: use the plan symbol to set out planting in the layout, then the matching elevation block to show the same plants in the wall views and sections. Combine them with furniture and hardscape blocks from the trees-and-plants and interior or outdoor libraries, and array the plan symbol along façades and paths to set out planting quickly and consistently.
Why plan and elevation symbols are not interchangeable
It is worth being deliberate about view: a plant block drawn in elevation does not work in plan, and vice versa. In plan you need the footprint — the canopy circle and pot — because the plan's job is to show area and position; in elevation you need the height and shape. Dropping the wrong one in is a common slip that makes a drawing read as careless.
Keep your plan-view planting on a dedicated layer so it can be frozen for a clean structural plan and thawed for the landscaped one, and screen it back so it sits behind the furniture and architecture rather than over them. If you set out a planting layout you reuse — a row of façade planters, a terrace arrangement — WBLOCK it into your library so a ready-made plan-view planting run is one insertion away on the next layout.
Free download
Browse the full library — DWG & DXF, no signup.
Questions
Frequently asked
How is a plan-view plant block different from an elevation one?+
It shows the plant from above — a canopy footprint circle rather than a side-on shape — so it works in floor plans, furniture layouts and roof plans. An elevation block, drawn face-on, belongs in wall elevations and sections; the two are not interchangeable.
Is the plan-view plant CAD block free for commercial use?+
Yes. It downloads free in DWG with no signup, no watermark and no attribution, and it is cleared for commercial project drawings as well as personal and student work.
What do I scale when I use a plan symbol?+
The canopy footprint — the diameter of the circle the plant occupies on the floor. Size it against the furniture and walls so the planting reads at the correct area; a planter that would block a walkway in reality should read that way in the plan.
How do I lay out a row of planters along a façade?+
The symbol is centred, so use ARRAY to repeat it evenly along the façade line, or a path array to follow a curved edge. Place each on its plant centre and keep the planting on its own layer so you can freeze it for a structural plan.
Related downloads
Blocks for this guide
Related categories
Related guides
Block landing
Free Flower Plant CAD Blocks — DWG Download
Free flower plant CAD blocks in DWG and DXF — flowering annuals and perennials in plan and elevation for AutoCAD landscape plans. No signup, commercial OK.
Block landing
Free Flowering Shrub CAD Blocks — DWG Download
Free flowering shrub CAD blocks in DWG and DXF — ornamental shrubs in plan and elevation for AutoCAD planting and site plans. No signup, commercial OK.
Block landing
Free Herb Plant CAD Blocks — DWG Download
Free herb plant CAD blocks in DWG and DXF — herbs for kitchen gardens, raised beds and planters, in plan and elevation for AutoCAD. No signup, commercial OK.